DESCRIPTION
Venetian Plaster is an interior acrylic Venetian plaster made with the highest quality ingredients. It is a unique decorative and protective coating designed for faux finishing, creating a polished, flat, pearlescent, metallic, or iridescent patina quickly and easily on walls, columns, and ceilings. Venetian Plaster provides dramatic results, high quality finishes and nearly endless design applications. It can simulate the visual effect of marble, granite and semi-precious stones with near infinite color variations.

USES
Use Venetian Plaster to create a faux finish, an old marble or granite look or an old world plaster look. Venetian Plaster can be applied over interior gypsum board and smooth plastered interior walls. Surfaces must be smooth and flat or skimmed with a leveling base coat or drywall compound to create a smooth, level surface.

ADVANTAGES

• A finishing product that is easy to use.
• Versatility of designs beyond compare.
• Near infinite color selections to complement existing interiors.
• Elegant and sophisticated interior theme.

PACKAGING

• Venetian Plaster: 1 gallon and 5 gallon pails
• Venetian Plaster Topcoat: 1 quart, 1 gallon and 5 gallon pail

COVERAGE
Coverage will vary depending on surface texture and porosity.

• Venetian Plaster: Approximately 200-250 sq. ft. per gallon
• Venetian Plaster Topcoat: Approximately 300-350 sq. ft. per gallon

COLORS/TEXTURES
Venetian Plaster is available in 15 standard colors and has endless texturing possibilities. Custom colors available for large jobs.

SURFACE PREPARATION
Surfaces must be dry and free from dirt or loose materials. Prime all glossy surfaces with an acrylic-based primer (or any water based flat paint that adheres to the surface adequately). Never install on rough or uneven substrates. Interior drywall should be finished to a Level 5 finish.

MIXING
Read the entire label before using this product.
Stir product throroughly to ensure uniform color and consistency.

APPLICATION
LaHabra recommends that the project owner or designer approve a job-site mock-upof the application of this product. The mock-up should demonstrate the products. appearance under the conditions given by the project specification(s). Application techniques will vary but the most popular application tools are metal trowels and spatulas.

1. Put product on a spatula or trowel and pull it tight to the wall.
2. Apply the first coat in a crosshatch manner thus skimming the wall with very thin coats. Since the material dries quickly, you can make your next pass in about 45 minutes.
3. Sand the surface lightly with 400-600 grit sandpaper, then apply the second coat in a similar manner to the first coat.
4. Apply texture, if applicable, in the third coat.
5. Polishing or burnishing can be done with steel spatulas, metal trowels, or a buffer to create the hard polished marble appearance. Sheen level is dependent on how much you polish or burnish.
6. Wax and other clear coats such as Venetian Plaster Topcoat may be applied, especially for areas that are exposed to moisture. Apply Venetian Plaster Topcoat using a flexible steel trowel, spatula or putty knife. Hold the trowel or putty knife at an angle, pulling and spreading a thin, even coat of the product across the surface, covering it completely. The topcoat may darken the color of the Venetian Plaster.

CLEAN UP
Clean tools frequently using clean water.

MAINTENANCE
LaHabra Venetian Plaster can be cleaned by a warm water rinse. Do not use harsh or abrasive cleaners.

STORAGE & HANDLING
Transport and store Venetian Plaster in closed, undamaged containers. DO NOT ALLOW TO FREEZE.

SHELF LIFE
If the product remains in an unopened, undamaged, original sealed pail that is properly transported and stored, Venetian Plaster has a shelf life of up to 1 year.

CAUTIONS AND LIMITATIONS

• For interior use only.
• Any area that has high moisture requires Venetian Plaster Topcoat.
• In case of contact with eyes, flush with clean water and seek medical attention if irritation persists.
• Use only on surfaces that are sound, clean, dry, unpainted, and free from any residue that might affect the ability of this product to bond to the surface.
• Ambient and surface temperatures must be 40° F (4° C) or higher during application and drying time. Provide supplemental heat and protection from precipitation as needed.
• Avoid application in direct sunlight in hot weather.
• Do not allow to freeze until completely dry.